Signalling Nomenclature

Individual signalling elements (signals, track circuits, points, level crossings) are identified by means of standard nomenclature. The trackside equipment, which generates the data for the signalling elements, may include solid-state interlocking (SSI) outputs, relay contacts, push buttons, levers and other indications.

In SOP Tables and ECS's, the first letter of an individual function denotes the general kind of the element. Preceding letters denote the function of the element, the equipment code, which consists of one or more letters.

The general rule has its exceptions. For example, TRTS and Route Elements have their own naming schemes. And finally, the name of an element doesn't necessarily start with a letter.

Element types

Code	Meaning
L	Latch
P	Points
R	Route
S	Signal
T	Track Circuit or Axle Counter Section

Train Ready To Start (TRTS) indications may be preceded by 'TRS' or 'TRTS'.

Equipment code

The table below denotes the characters of an equipment code (from GK/RT0205 Appendix D):

Descriptive Term (preceding letters)		Apparatus (last letter)
A	Approach; Automatic; Relay Contact – Arm	A	Axle Counter
B	Block; Bolt; Relay Contact – Back	B	Block Instrument
C	Checking or Providing; Coding	C	Contact
D	Clear (green); Decoding; Relay Contact – De-energised
E	Light; Lamp; Heat (externally applied); Emergency; Earth	E	Light; Lamp; Earth
F	Fog; Flashing; Feed; Relay Contact – Front	F	Detonator Placers
f	Frequency	f	Fuse
G	Signal	G	Signal Apparatus
H	Caution (yellow)	H	Capacitor
HH	Preliminary Caution (double yellow)
I	AWS	I	Inductor
J	Time (delayed action)	J	Rectifier; Diode
K	Indicating or Detecting	K	Indicator Electro-mechanical
L	Locking; Left	L	Lock
M	Marker; Magnetic	M	Motor
N	Normal	N	Release; Hand Operated Switch; Push Button or Key
O	Retarding	O	Resistor; Heater
P	Repeating	P	Lever Latch or Trigger Contact
Q	Treadle or Bar	Q	Local Coil of a Double Element Relay; Treadle or Bar
R	Reverse; Right; Danger (red)	R	Relay or Contactor
Rx	Receiving	Rx	Receiver
S	Stick
T	Track Circuit	T	Transformer
Tx	Transmitting	t	Terminal
U	Route	U	Unit
V	Trainstop (including TPWS)	V	Trainstop (including TPWS) Apparatus
W	Points	W	Point Operating Apparatus
X	Audible Annunciator; Level Crossing; Wrong Direction	X	Audible Annunciator (bell, buzzer, horn, etc.)
Y	Slotting or Disengaging	Y	Slotting or Disengaging Apparatus
Z	Special	Z	Special Unit

Routes

Typically, the name of an individual route consists of three parts: the signal number, route letter and class. However, the order and number of these parts may vary.

Examples on how to interpret different naming conventions:

Name	Signal Number	Route Letter	Class
R101(M)A	101	A	M
R101A(M)	101	A	M
R101AM	101	A	M
R101M	101		M
RAW149BMC	AW149	B	M and C
R229XA(S)	229X	A	S

Route letter

The route letter ('A', 'B', 'C', ...) denotes the individual path taken from a signal through a set of points and/or lines. All signals have at least one route. The 'A' route is the furthest signalled route to the left, in the direction of travel. The following routes are lettered on alphabetic order from left to right.

Route class

The last character is the route class (by specification, in brackets):

Code	Type	Meaning
(M)	Main route	This is a route set from a main signal. The driver may proceed at main signal's aspect.
(C)	Call-on route	This is a permissive working for a main route and allows a train to enter a section already occupied by another train. The driver must proceed with caution (< 10 mph).
(S)	Shunt route	This is a route set from a shunting signal, which may be attached to a main signal or placed on the ground. The driver must pass the signal with caution at a speed which allows the train to stop short of any obstruction.
(W)	Warner route	This may be used when a full overlap is not available beyond the exit signal of a route. The signal will stay at danger (red) until it changes to caution (yellow) at the time the train stops in front of the signal.
(PS)	Proceed on Sight Authority	The signal will notionally be used where the route setting and locking function is still proved to be operable but a function such as train detection or lamp proving of a signal ahead may be failed.

Signals

Code	Meaning
BR, R	Repeater signal
RGE	Electric lamp illuminating danger aspect (Red)
HGE	Electric lamp illuminating caution aspect (Yellow)
DGE	Electric lamp illuminating clear aspect (Green)
RGK	Electro-Mechanical Indicator showing signal at danger aspect (red)
HGK	Electro-Mechanical Indicator showing signal at caution aspect (yellow)
DGK	Electro-Mechanical Indicator showing signal at clear aspect (green)
OFF, OFFG, OFFK	Signal at any other state than danger (red)
LOSECK	Limit of Shunt lamp checking indicator

Points

Code	Meaning
GF	Ground frame
FK	Electro-mechanical indicator showing ground frame points in local operation
N	Normal position
NK	Electro-mechanical indicator showing normal position
NWK	Electro-mechanical indicator showing points in normal position
R	Reverse position
RK	Electro-mechanical indicator showing reverse position
RWK	Electro-mechanical indicator showing points in reverse position